Por favor, use este identificador para citar o enlazar este ítem: https://repositorio.uta.edu.ec/jspui/handle/123456789/30652
Título : Análisis de soldadura del acero inoxidable martensítico AISI 420 con acero de medio carbono AISI 1045 y bajo carbono AISI 1018 por soldadura SMAW y su influencia en las propiedades mecánicas
Autor : Vaca Ortega, Wilson Henry
Acosta Acosta, Christian Javier
Palabras clave : SOLDADURA SMAW
ACERO INOXIDABLE
AISI 420
ACERO DE MEDIO CARBONO
AISI 1045
BAJO CARBONO
AISI 1018
PROPIEDADES MECÁNICAS
ENSAYO DE MATERIALES
ELECTRODOS
Fecha de publicación : 2020
Editorial : Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, Carrera de Ingeniería Mecánica
Resumen : The work was carried out with the objective of choosing a suitable electrode to weld a martensitic stainless steel with a medium and low carbon steel in order to generate technological benefits in the industry, as well as study the microstructural changes that may have problems in this material during the welding process which makes it necessary to study the union of these materials. This project was carried out with the SMAW process under the AWS code B4.0 "Standard methods for mechanical welding tests" which establishes the general provisions for the realization of the tensile and impact probes for the joints of AISI 420 stainless steel joints with AISI 1045 medium carbon steel and AISI 1018 low carbon steel using input materials E 308L-16, E 3016L-16 and E 312-16. The tests were carried out in the laboratories of the Center for Productive Development of Mechanical Metalworking of the Municipal Government of Tungurahua. After having performed the required tests, the procedure is analyzed with the respective analysis and interpretation of the results, and the best mechanical properties found in the union of the stainless steel AISI 420 stainless steel and AISI 1018 low carbon steel with the material of E312-16 contribution obtaining a maximum effort of 613,61 MPa, in addition to an elongation percentage of 16.79 percent likewise the impact energy of 61.27 J and a maximum hardness of 269.38 VHI.
Descripción : El trabajo se realizó con el objetivo de elegir un electrodo adecuado para soldar un acero inoxidable martensítico con un acero de medio y bajo carbono con el fin de generar beneficios tecnológicos en la industria metalmecánica, así mismo estudiar los cambios micro estructurales que pueden ocurrir en este material durante el proceso de soldadura lo que hace necesario estudiar la unión de estos materiales. Este proyecto se realizó con el proceso SMAW bajo el código AWS B4.0 “Standard Methods for Mechanical Testing of Welds” el cual, establece las disposiciones generales para la realización de las probetas de tracción e impacto para las juntas de acero inoxidable martensítico AISI 420 con acero de medio carbono AISI 1045 y acero de bajo carbono AISI 1018 utilizando materiales de aporte E 308L-16, E 3016L-16 y E 312-16. Los ensayos fueron realizados en los laboratorios del Centro de Fomento Productivo Metal Mecánico Carrocero del Gobierno Municipal de Tungurahua. Luego de haber realizado los ensayos requeridos se procedió con su respectivo análisis e interpretación de los resultados, y se logró determinar que las mejores propiedades mecánicas se encontraban en la unión del acero inoxidable martensítico AISI 420 y acero de bajo carbono AISI 1018 con el material de aporte E312-16 obteniendo un esfuerzo máximo de 613,61 MPa, además un porcentaje de elongación de 16,79 por ciento, de igual manera la energía de impacto de 61,27 J y una dureza máxima de 269,38 VHI.
URI : https://repositorio.uta.edu.ec/jspui/handle/123456789/30652
Aparece en las colecciones: Ingeniería Mecánica

Ficheros en este ítem:
Fichero Descripción Tamaño Formato  
Tesis I. M. 573 - Acosta Acosta Christian Javier.pdfTESIS A TEXTO COMPLETO9,59 MBAdobe PDFVisualizar/Abrir


Los ítems de DSpace están protegidos por copyright, con todos los derechos reservados, a menos que se indique lo contrario.