Ingeniería Civil y Mecánica

URI permanente para esta comunidadhttp://repositorio.uta.edu.ec/handle/123456789/898

Examinar

Resultados de la búsqueda

Mostrando 1 - 6 de 6
  • Item type:Ítem,
    Análisis comparativo de la resistencia a compresión y resistencia a flexión del hormigón convencional f’c = 210 kg/cm2 y el hormigón con adición de fibras de totora
    (Universidad Técnica de Ambato-Facultad de Ingeniería Civil y Mecánica-Carrera de Ingeniería Civil, 2026-07-01)
    Cunalata Gallardo Valeria Abigail
    ;
    Ureña Aguirre Maritza Elizabeth
    ;
    Universidad Técnica de Ambato-Facultad de Ingeniería Civil y Mecánica-Carrera de Ingeniería Civil
    The present research aimed to comparatively analyze the compressive strength and flexural strength of conventional concrete f'c = 210 kg/cm² and concrete with the addition of natural bulrush fibers (Schoenoplectus californicus). The study arises from the need to develop sustainable construction materials that can improve certain mechanical properties of concrete by utilizing natural resources available in Ecuador. The methodology employed was quantitative and experimental. Standard concrete mixes and mixes with the addition of bulrush fiber in percentages of 0.50%, 1.00%, and 1.50% relative to the volume of the mix were prepared. Previously, the physical and mechanical characterization of the constituent materials was carried out in accordance with the NTE INEN, ASTM, and ACI standards. Subsequently, cylindrical and prismatic specimens were manufactured, which were subjected to compression and flexural tests at ages of 7, 14, and 28 days. The results allowed for the identification of the influence of bulrush fiber on the mechanical behavior of concrete. It was observed that the incorporation of fiber at 0.50% generates improvements in flexural strength due to the bridging effect of cracks and redistribution of stresses within the cementitious matrix. However, high increases in fiber content can lead to reductions in compressive strength due to the formation of voids, compaction difficulties, and increased water demand. Finally, it was determined that bulrush fiber constitutes a viable alternative for applications where flexural strength and environmental sustainability are relevant factors.
  • Item type:Ítem,
    Comparación de diseños de vigas de alma abierta con conectores de corte de perfil angular y de varilla corrugada para determinar su grado de eficiencia
    (Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica. Maestría en Ingeniería Civil con Mención en Estructuras Metálicas., 2025)
    Oña Cifuentes Cristian Jair
    ;
    Cevallos Cabrera Jorge Washington
    The purpose of this article is to compare the strength and deflections at the yield limit and maximum capacity provided by the composite system of an open-web beam with a solid slab and shear connectors using corrugated rebar and angles. The specimens were fabricated using materials from Ambato y Quito, Ecuador, including ASTM A36 steel, ASTM A615 steel, and concrete with a compressive strength of f'c = 210 kg/cm². These comparisons were based on the results obtained from a four-point bending test conducted on two six-meter-long specimens with corrugated rebar connectors and two with angle connectors. This research analyzed the efficiency of the specimens in dissipating energy in the elastic and plastic regions, their ductility, stiffness, structural behavior regarding deformations, and failure modes during the interactive load versus deflection process. The average capacity for each type of connector was determined, and comparative calculations were performed, revealing a 16% variation in the yield limit and a 6% variation in the plastic limit, concluding that the two systems differ in structural strength. The results also validate the accuracy of the calculation methodologies for the beam’s nominal moment resistance and the precision of the formulations adapted for shear connectors using rebar and angles, given that AISC and SJI do not provide a specific method for this type of connection.
  • Item type:Ítem,
    Valoración de la resistencia a flexión de hormigón reforzado con fibra de caña de azúcar y yute
    (Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, Carrera de Ingeniería Civil, 2024-08)
    Mena Alomoto, Angie Patricia
    ;
    Ureña Aguirre, Maritza Elizabeth
    Construction industries are among the most responsible for global environmental pollution, the extraction and processing of raw material for concrete generates amounts of energy (CO2), the commonly used reinforcement is steel and the industries produce an amount of greenhouse gases and solid waste that pollute the air and water quality. This experimental work seeks to offer an environmentally friendly alternative for the reinforcement of concrete using natural fibers and analyzed the effect on the flexural strength, we began by carrying out a survey of the production of sugar cane and jute in Ecuador, to understand the geographical distribution and production volumes in the provinces, In addition, traditional concrete beams and beams with sugar cane and jute fibers in longitudinal and transverse direction with thickness of 6 millimeters and 3 millimeters were elaborated, and the results were compared between these beams, also the type of failures that are produced and how the fibers contribute to the pathologies were observed. It is shown then that the concrete beams with jute fibers in longitudinal direction and with a thickness of 3 millimeters present a higher resistance than the standard concrete, while the cane fibers maintained the resistance within the minimum range of the traditional concrete and the deformations of the jute fibers are lower than those of the standard concrete, helping to reduce the failures in the whole section of the beam.
  • Item type:Ítem,
    Evaluación de la resistencia a flexión de vigas de hormigón armado preparado con agregado grueso reciclado y adicionando catalizador agotado de craqueo catalítico fluidizado
    (Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, Carrera de Ingeniería Civil, 2024-08)
    Álvarez Martínez, John Anderson
    ;
    Navarro Peñaherrera, Carlos Patricio
    Due to the existing environmental problems in the construction industry, the use of recycled coarse aggregates was chosen for the production of reinforced concrete beams. In this way, this research focused on the design of beams with which the flexural resistance was determined, with the compressive strength of the concrete used being 280 kilograms per square centimeter, adding spent catalyst from fluidized catalytic cracking as a partial substitute. of fine aggregate by 5 and 10 percent, and completely replacing conventional coarse aggregate with crushed coarse aggregate from recycled concrete elements. For this project, physical and mechanical tests were carried out on both natural aggregates and substitute aggregates, in the case of recycled coarse aggregate and spent catalyst, following the technical standards in force in Ecuador (NTE-INEN). In this way, the flexural strength of reinforced concrete beams prepared with recycled coarse aggregate and spent catalyst from fluidized catalytic cracking was evaluated. Substitute materials were obtained and tests required under the regulations were carried out, both on recycled aggregates and on natural aggregates. The results showed that the beams with 10 percent spent catalyst from fluidized catalytic cracking replacing the fine aggregate and coarse aggregate recycled from crushed concrete elements, presented a greater flexural strength at 28 days compared to the beams with 5 percent replacement and those made with conventional materials.
  • Item type:Ítem,
    Evaluación del acero estructural reforzado con fibra de carbono unidireccional mediante el método de ensayo a flexión de tres puntos, descrito en la normativa ASTM E290- 22 para determinar el incremento de resistencia
    (Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, Carrera de Ingeniería Mecánica, 2023-09)
    Pullopaxi Aimacaña, Willian Hernan
    ;
    Peña Jordán, Francisco Agustín
    The need for a method to rehabilitate a structural member has increased significantly due to the increase in magnitudes in live load. The reconditioning method using steel plate is not a viable solution due to the added weight, difficulty of fixing and welding problems, as well as being prone to corrosion and fatigue. Previous research, determined that there is a directly proportional relationship between roughness and adhesive strength, also developed alternative methods of surface cleaning, to improve adhesive bonds, because of this we proceeded to evaluate how the contact area influences depending on the flexural strength, obtaining results when applying the three-point bending test described in the ASTM E290-22 standard, In addition, the compressive properties of the adhesive were analyzed by means of a group of specimens dimensioned according to the ASTM D695 standard, however a mathematical model was implemented to establish differences between tests. With the present investigation we compared the results obtained from the behavior of structural steel ASTM A-36 reinforced with unidirectional carbon fiber adhered by a high strength thixotropic adhesive, in a three-dimensional format, in two groups of specimens, which one of them did not have reinforcement, evidencing the doubled increase in resistance, the group that presented the best results for not having failure due to detachment, was the one with the largest contact area with an average value of 10,646 micrometers and a maximum flexural effort of 893.05 MPa.
  • Item type:Ítem,
    Análisis del comportamiento a flexión del hormigón reforzado con fibras plásticas (polipropileno) después de las altas temperaturas
    (Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, Carrera de Ingeniería Civil, 2023-09)
    Murillo Estrada, Ariel Mateo
    ;
    Ramírez Cabrera, Wladimir José
    Reinforced concrete is one of the most widely used structural elements in Ecuadorian constructions. By the fourth quarter of 2022, 79.5 percent of the material present in the structure was registered, that is, the predominant material in the country. Being so widely used, the question arose how high temperatures affect simple concrete compared to fiber-reinforced concrete. The present work studied the influence of polypropylene fibers in plain concrete after being affected at high temperatures. Obtaining a correct dosage was achieved by analyzing the characteristics of the fine and coarse aggregates, then the required resistance was verified by means of the compression test in cylindrical specimens for resistances of 210 and 240 kg/square centimeters. Once the resistance was obtained, beam-type test tubes of dimensions 10x10x35 centimeters were made where 2 dosages were used with respect to the macrofiber with 0 and 3 kg/cubic meters. After curing the specimens for 28 days, they were subjected to different temperatures: 20, 100, 280 and 600 degrees Celsius. Subsequently, the respective flexural tests (ASTM 1609) were carried out, for the elaboration of the stress vs. deflection graph where the behavior of the concrete without fibers and with fibers was compared. The comparison of the resistances and the addition of fibers in the specimens allowed us to verify the influence of these at high temperatures, improving their resistance to flexion at all exposure temperatures.