Por favor, use este identificador para citar o enlazar este ítem: https://repositorio.uta.edu.ec/jspui/handle/123456789/37104
Título : Análisis del proceso de soldadura GTAW y su incidencia en las propiedades mecánicas en juntas a tope del acero AISI 304 empleadas en la industria alimenticia
Autor : Vaca Ortega, Wilson Henry
Pazmiño Chimbana, Jonathan Ricardo
Palabras clave : SOLDADURA
PROPIEDADES MECÁNICAS
RESISTENCIA A TRACCIÓN
IMPACTO
DUREZA
MATERIAL DE APORTE
JUNTAS A TOPE
JUNTAS A BISEL
PASES DE SOLDADURA
Fecha de publicación : ene-2023
Editorial : Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, Carrera de Ingeniería Mecánica
Resumen : In the food industry, it has been observed that in the manufacture of hoppers there is no analysis of the mechanical properties in butt and bevel weld joints using AISI 304 stainless steel with ER308L, ER309L and ER316L filler material through a GTAW welding process. Among the most relevant mechanical properties we highlight the tensile strength MPa, Brinell hardness (HB) and absorbed energy (J), these mechanical properties can vary by the type of joint, thickness and filler material. The development of this investigative work is based on the AWS D1.6 standard, which establishes general welding parameters for stainless steels, for butt and bevel welding of the plate at 6 mm thickness, the root pass was required., the hot pass and the finish pass while for welding on 3mm thick plates, 2 root and finish passes were carried out. The mechanical tests were carried out in the body building development center of the city of Ambato and with the help of trained technicians, more precise data was obtained from each test carried out. The data obtained in the equipment were tabulated to relate them and to be able to determine which filler material gives us a better mechanical behavior when welding AISI 304 steels.
Descripción : En la industria alimenticia se ha observado que en la elaboración de tolvas no existe un análisis de las propiedades mecánicas en las juntas de soldadura a tope y bisel empleando acero inoxidable AISI 304 con material de aporte ER308L, ER309L y ER316L mediante un proceso de soldadura GTAW. Entre las propiedades mecánicas más relevantes destacamos la resistencia a la tracción MPa, dureza Brinell (HB) y energía absorbida (J), estas propiedades mecánicas pueden variar por el tipo de junta, espesor y material de aporte. El desarrollo de este trabajo investigativo está basado en la norma AWS D1.6 en la cual se establece parámetros generales de soldadura para los aceros inoxidables, para la soldadura a tope y bisel de la placa a 6 mm de espesor se necesitó el pase de raíz, el pase en caliente y el pase de acabado mientras que para la soldadura en placas de 3mm de espesor se llevó a cabo 2 pases el de raíz y acabado. Los ensayos mecánicos fueron ejecutados en el centro de fomento carrocero de la ciudad de Ambato y con la ayuda de técnicos preparados se obtuvieron datos más precisos de cada ensayo realizado. Los datos obtenidos en los equipos fueron tabulados para relacionarlos y poder determinar que material de aporte nos brinda un mejor comportamiento mecánico al soldar acero AISI 304.
URI : https://repositorio.uta.edu.ec/jspui/handle/123456789/37104
Aparece en las colecciones: Ingeniería Mecánica

Ficheros en este ítem:
Fichero Descripción Tamaño Formato  
Tesis I.M. 721 - Pazmiño Chimbana Jonathan Ricardo.pdfTESIS A TEXTO COMPLETO27,03 MBAdobe PDFVisualizar/Abrir


Los ítems de DSpace están protegidos por copyright, con todos los derechos reservados, a menos que se indique lo contrario.