Por favor, use este identificador para citar o enlazar este ítem: https://repositorio.uta.edu.ec/jspui/handle/123456789/32147
Título : Diseño y construcción de un sistema de generación eléctrica utilizando energía hidráulica de canales de riego
Autor : Arroba Arroba, César Hernán
Acosta Peña, Alex Vinicio
Moya Cepeda, Raúl Alfredo
Palabras clave : ENERGÍA HIDRÁULICA
CANALES DE RIEGO
TURBINAS DE REACCIÓN
TURBINAS DE IMPULSO
MICROHIDROGENERACIÓN
GENERADOR
Fecha de publicación : feb-2021
Editorial : Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, Carrera de Ingeniería Mecánica
Resumen : The objective is to design and build an electricity generation system using irrigation channels, in order to evaluate the potential that irrigation channels have generating electricity, as well as to find new renewable and sustainable energy sources. The irrigation channel that will be used in this research is the Huachi – Pelileo channel. The methodology begins with the collection of data on the speed of water and the flow that exists in the irrigation channel. The ANSYS software was used for the design of the turbine, in which the existence of cavitation in the turbine blades and the resistance of the turbine components were analyzed based on the Von Mises failure criteria. Then, the transmission system was designed based on the calculated rotation speed of the turbine and the speed required by the generator to operate. Finally, the construction and the evaluation of the generation system was carried out. The result obtained was a maximum power of 422.1 Watts in the test carried out in the workshop, in which the correct operation of the generation system was guaranteed. However, a simulation carried out in the SolidWorks software determined a maximum power of 1 kilo Watts. This value is due to the fact that the environment of the irrigation channel could not be recreated in the workshop.
Descripción : El objetivo es diseñar y construir un sistema de generación eléctrica utilizando canales de riego, con el fin de evaluar el potencial que tienen los canales de riego en la generación de electricidad, además de encontrar nuevas fuentes de energía renovable y sostenible. El canal de riego que se va a utilizar en esta investigación es el canal Huachi – Pelileo. La metodología empieza con la recolección de datos sobre la velocidad del agua y el caudal que existe en el canal de riego. Para el diseño de la turbina se utilizó el software ANSYS, en el cual se hizo el análisis de la existencia de cavitación en los alabes de la turbina y la resistencia de los componentes de la misma tomando como base el criterio de falla de Von Mises, luego el sistema de transmisión se diseñó en base a la velocidad de rotación calculada de la turbina y la velocidad que necesita el generador para funcionar. Finalmente, se procedió a la construcción y evaluación del sistema de generación. El resultado que se obtuvo fue una potencia máxima de 422.1 Watts en las pruebas realizadas en el taller, en el cual se garantizó el correcto funcionamiento del sistema de generación, sin embargo, una simulación realizada en el software SolidWorks determinó una potencia máxima de 1kilo Watts, este valor es debido a que en el taller no se pudo recrear el ambiente del canal de riego.
URI : https://repositorio.uta.edu.ec/jspui/handle/123456789/32147
Aparece en las colecciones: Ingeniería Mecánica

Ficheros en este ítem:
Fichero Descripción Tamaño Formato  
Tesis I. M. 620 - Acosta Peña Alex Vinicio y Moya Cepeda Raúl Alfredo.pdfTESIS A TEXTO COMPLETO5,97 MBAdobe PDFVisualizar/Abrir


Los ítems de DSpace están protegidos por copyright, con todos los derechos reservados, a menos que se indique lo contrario.