Ingeniería Civil y Mecánica
Permanent URI for this communityhttp://repositorio.uta.edu.ec/handle/123456789/898
Browse
3 results
Search Results
Item Diseño y construcción de una bomba de ariete que será ubicada en el patio central de la Facultad de Ingeniería Civil y Mecánica.(Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, Carrera de Ingeniería Mecánica, 2025-02) Flores Gordillo, Andrés Mateo; Escobar Luna, Luis EduardoThe purpose of the project is to design and build a single-impeller ram pump, a hydraulic device that harnesses the energy of a flow of water to lift a portion of it without the need for electrical power. This type of pump is ideal for irrigation systems, water supply and educational activities that teach principles of hydraulics and engineering. The ram pump will be installed in the central courtyard of the Faculty of Civil and Mechanical Engineering, which will allow students and professors to interact directly with the device, favoring practical teaching and experimentation in the academic environment. The design comprises the principles of fluid mechanics and the ram pump was manufactured using accessible materials such as stainless steel or PVC for its main components (tubes, valves, compression chamber, etc.). Key aspects of the hydraulic system were considered, such as the available water flow and pressure fluctuations and the height at which the feed tank should be, in order to optimize its performance, it was possible to conclude that the output flow rate is 5.71 liters per minute, thus achieving a continuous flow for the cascade type water source for the benefit of the learning of the students of the Mechanics Career. As a result, special attention was paid to the educational functionality of the project, ensuring that it serves as a learning tool for the understanding of hydraulic and mechanical concepts, fostering curiosity and academic development of future engineers.Item Diseño de un sistema de bombeo mediante ariete hidráulico para la comunidad “Chilcapamba” del cantón Mocha(Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, Carrera de Ingeniería Mecánica, 2022-01) Chicaiza Palacios, Kevin Ernesto; Escobar Luna, Luis EduardoIn this technical project a single-impeller ram pump is designed using Krol's mathematical model, each of the parts are modeled according to the calculations previously made. It is based on the available flow of the community of Chilcapamba, taking into account the unevenness of the terrain, the most optimal design is sought. In the design of the pump, maximum pressure values of approximately 0.3 MPa, dynamic pressure of 8.2 Kpa and speed in the impulsion valve of 2.87 m/s were found. The modeling is done in a CAD program, where each of the parts is detailed, especially the discharge valve, after this the simulation of the pump operation is performed in order to corroborate the data calculated analytically, the simulation is carried out with boundary conditions according to your requirement, where the mesh metric had a value of very good with this ensuring valid results and very close to reality. As for results, the most important parameters were simulated where the results of velocity in the valve, dynamic pressure in the valve and maximum pressure in the body of the ram were obtained obtaining values of 0.382 m/s, 8107 Pa and 380453 Pa respectively, also reflects a result where the areas of greater turbulence is observed. These values were compared with those mentioned above by means of a relative error study where values from 0.01 to 0.29 were found. With this it could be observed that 3 of the 4 analyzed values comply with the requirement of having a percentage lower than 0.16 to be validated, while one of them is out of phase, but not considerablyItem Estudio de factores hidráulicos en una bomba de ariete y su efecto sobre la eficiencia(Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica. Carrera de Ingeniería Mecánica., 2013) Galarza Chacón, Raúl Fernando; Mayorga Pardo, Alex SantiagoEl presente trabajo de investigación se realizó con la finalidad de analizar el cambio de los factores hidráulicos en una bomba de ariete y su efecto sobre la eficiencia, tanto teórica como experimental. Este trabajo se basó en la modificación del diseño mecánico del Ariete Hidráulico convencional por un ariete multimpulsor, teniendo como objetivo la configuración idónea de la válvula de impulsión mejorando su eficiencia, lo que se comprobó mediante la instalación de la bomba. Para esto se diseñó un sistema de válvulas colocadas en serie (ariete multimpulsor), aprovechando el caudal y la energía remanente que generalmente se desperdicia. Mediante la instalación de la bomba se comprobó que el ariete de tres impulsores es el más eficiente, para lo cual se tomaron tres valores de carrera de 3, 5 y 10mm utilizando contrapesos de 0,6 y 1,6 kg. En cada configuración fueron evaluadas las relaciones entre caudal y altura de descarga, observando que existe una relación directa entre carrera y peso de la válvula de impulsión. De los ensayos realizados se observó que la eficiencia del ariete llega a su máximo cuando se tiene una moderada altura de entrega. Sin embargo, en el caso de una válvula de impulsión con contrapeso liviano, la eficiencia va a decrecer al aumentar la altura de descarga. Finalmente la investigación reveló que con la configuración de 3 válvulas, carrera de 10mm y peso de 0,6 kg se obtiene un caudal de 8 litros/min, altura de descarga de 2,5m y eficiencia de 28,57%, siendo la más apropiada si se necesita elevar grandes caudales; pero si se utiliza 3 válvulas, carrera de 10 mm y peso de 1,6 kg se obtiene un caudal de 1 litros/min ,altura de descarga de 32m y eficiencia de 22,86%, siendo la apropiada si se necesita descargar a una altura mayor. Por tanto se concluye que el uso del ariete multimpulsor es más adecuado que el ariete convencional cuando se habla de eficiencia.