Ingeniería Civil y Mecánica
URI permanente para esta comunidadhttp://repositorio.uta.edu.ec/handle/123456789/898
Examinar
2 resultados
Resultados de la búsqueda
Item type:Ítem, Diseño de conexiones entre perfiles conformados en frío de sección UV en acero ASTM A36, utilizados para la construcción de torres de telecomunicaciones(Universidad Técnica de Ambato-Facultad de Ingeniería Civil y Mecánica-Carrera de Ingeniería Mecánica, 2026-07-05) ;Candilejo Simbaña Adrián Alexander ;Martinez Chuncha Alex Daniel ;Peña Jordán Francisco AgustínUniversidad Técnica de Ambato-Facultad de Ingeniería Civil y Mecánica-Carrera de Ingeniería MecánicaThis research focused on the design and evaluation of a bolted connection between cold-formed UV-section profiles made of ASTM A36 steel, intended for telecommunication tower structures. The study arose from the need to improve the behavior of lightweight steel connections subjected to axial loads, since local failure mechanisms can affect the stability of the structural system. For this purpose, a connection configuration was proposed using 6 mm thick UV profiles, 8 mm connection plates, and galvanized A325 bolts. The methodology combined experimental tensile and compression tests on assembled specimens to determine the mechanical response, maximum load and displacement, and associated failure modes. In parallel, finite element models were developed to represent the behavior of the connection under axial loading. The comparison between experimental and numerical results was carried out using the average maximum load as the main evaluation parameter. In tension, an average experimental load of 276,20 kN was obtained, while the finite element model reached 254,22 kN, with a percentage error of 7,96 %. The failure mode was associated with local damage around the holes. In compression, an average experimental maximum load of 258,36 kN was obtained, while the finite element model reached 238,64 kN, with a percentage error of 7,63 %. The failure mode was associated with local buckling of the profile webs and the connection plate. The models reproduced the failure mode and load-bearing capacity of the proposed connection.Item type:Ítem, Diseño de perfiles conformados en frio de sección UV, de acero ASTM A36 utilizados para la construcción de torres de telecomunicaciones.(Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica. Maestría en Ingeniería Civil con Mención en Estructuras Metálicas, 2024-10) ;Molina Peralvo, Fabián Alexander ;Peña Jordán, Francisco AgustínUniversidad Técnica de Ambato. Facultad de Ingeniería Civil y MecánicaIt is a challenge for engineering to modernize telecommunications structures by improving their strength and reducing failure rates under higher wind loads. It is essential to deepen the understanding of the behavior of these structures. The objective of this research was to design a UV-shaped profile in ASTM A36 cold-formed steel, in accordance with AISI 100-16 standards, for application in telecommunications towers. During the development of the project, it was analyzed whether there was a reduction in the effective area following the parameters of the AISI S902 standard, comparing these results with a mathematical model and conducting laboratory tests. As a result, no reduction in the effective area was observed in the UV profiles; in the tests, which are the most accurate method, no significant change was detected. This information was corroborated through hypothesis testing. On the other hand, the design of these profiles was optimal, and their strength meets the applied methodology. A wind load of 1500 kgf was assumed, which pushed a section of a triangular crosssection tower to its limit, achieving a demand-capacity ratio of 87 percent, demonstrating that the UV-shaped profile is suitable for structural use. Finally, following the AISI 100-16 methodology allowed for the establishment of criteria for efficient design, providing specific guidelines that ensure the profiles meet the safety and performance standards required for use in telecommunications towers. It was identified that UV-shaped profiles offer good performance in terms of structural strength, making them an efficient and economical option for this type of structure.
