Ingeniería Civil y Mecánica
URI permanente para esta comunidadhttp://repositorio.uta.edu.ec/handle/123456789/898
Examinar
10 resultados
Resultados de la búsqueda
Item type:Ítem, Diseño de un sistema de pistolas Dumming para un sistema Jig de la línea de producción Shineray X30, para la empresa Ciudad Del Auto Ciauto Cia.Ltda basado en un análisis de factibilidad(Universidad Técnica de Ambato-Facultad de Ingeniería Civil y Mecánica-Carrera de Ingeniería Mecánica, 2026-07-08) ;Mayorga Ortiz Esteban Alejandro ;Vargas Tello José Ignacio ;Carrillo Rosero Carlos MauricioUniversidad Técnica de Ambato-Facultad de Ingeniería Civil y Mecánica-Carrera de Ingeniería MecánicaThis project was carried out at Ciudad del Auto CIAUTO CÍA. LTDA., specifically on the Shineray X30 body production line, where it was identified that the spot welding process at the side panel and floor assembly station was performed manually, resulting in operational limitations related to non-productive time, restricted accessibility to the work area, operator overexertion, and elevated cycle times within the station. In order to optimize this process, a semi-automated system of self-actuated Dummy welding guns was designed and implemented, integrated into the existing production JIG while considering the geometric, structural, pneumatic, electrical, and quality requirements demanded by the automotive industry. The applied methodology combined field, bibliographic, and experimental methods, allowing the analysis of the station’s real operational behavior, the development of tower-type support structures for the precise positioning of the welding guns, and the technical validation of the system under actual operating conditions. The implementation significantly reduced direct operator intervention in hard-to-access areas, particularly on the underside of the vehicle body, while also reducing the process cycle time from 16 minutes and 23 seconds to 2 minutes and 26 seconds, maintaining a 100% acceptance rate of the weld spots according to the criteria established by the AWS D8.1M/D8.1 standard and the company’s internal quality requirements. Furthermore, the results demonstrated operational savings of approximately 111.96 man-hours per month, enabling the redistribution of human resources to higher-demand production lines without increasing operational workload. From a production perspective, the daily manufacturing capacity increased from an average of 12 to 14 units, representing an approximate 16.67% increase in productivity while maintaining the same number of operators. Finally, the technical-economic analysis determined that the proposed system is both operationally viable and financially feasible, since the improvements in productivity, reduction of non-productive times, and optimization of human resources contribute to a progressive return on investment throughout the estimated service life of the implemented system.Item type:Ítem, Estudio del reforzamiento estructural de varillas de acero ASTM A706 mediante un proceso de soldadura SMAW y su incidencia a las propiedades mecánicas(Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica. Maestría en Ingeniería Civil con Mención en Estructuras Metálicas, 2024-09) ;Villacrés Quintana, Stephany DanielaParedes Salinas, Juan GilbertoIn Ecuador, in the placement of structural rod, to comply with lengths that exceed the 12 meters that a commercial rod measures, it is common to make overlaps tied with wire, welding being an uncommon alternative in the middle, however, in the overlaps tied, critical points are created, which is why the need has been seen to analyze the welding since currently the municipal GAD requests that they be welded, this being a motivation to study the structural reinforcement of ASTM A706 steel rods, which is marketed in the country, through a SMAW welding process and its impact on the mechanical properties for which we will rely on the AWS D1.4 code, which deals with reinforcing bars and provides guidelines for welding them. In this project, an experimental methodology was used, an analysis of different welding processes was carried out on ASTM A706 structural steel rods, for the selection of the electrode, specific electrodes were chosen for welding ASTM A706 steel that meet the specifications and requirements. of the project As results, it was obtained that in the visual analyzes of the rods there were porosity and overmount failures, which were acceptable according to the specifications of the AWS D1.4, in the tensile tests it was obtained that the rods as a base material resisted on average 602.88 MPa, and that the cases that resisted the most tensile stress were the one in which electrode 6011 and type V joint was used with 508.46 MPa and the one that was carried out with electrode 7018 and double V joint with 492.60 MPa of ultimate stress As for the macrographs, the correct fusion of the materials was visualized, both in overlap and in a V joint. As a conclusion, we can obtain that the welding in the aforementioned cases reaches high tensile stresses, however it does not equal that of the base material. , so it is proposed for future studies to analyze the mechanical properties of the material with other types of electrodes or welding processes.Item type:Ítem, Estudio del proceso de soldadura del sistema de anclaje placa base-varilla, y su incidencia en las propiedades mecánicas de una edificación de cuatro plantas de una estructura metálica(Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica. Maestría en Ingeniería Civil con Mención en Estructuras Metálicas, 2024-05) ;Mayanza Balla, Janneth AlexandraParedes Salinas, Juan GilbertoIn the national context of Ecuador, where construction and urban development are fundamental for economic and social growth, the need arises to investigate and understand in depth the welding process of the base plate - rod anchorage system and its impact on the mechanical properties of metal structure buildings. The safety and durability of buildings are essential aspects to ensure the protection of lives and property, as well as to boost confidence in the country's infrastructure. The methodology applied in this research included linear static and spectral modal design, using standards such as AISC 360-16 and NEC 2015 to obtain reactions that would allow the adequate design of the base plate. In addition, the macrograph visual inspection test was used to evaluate the weld quality and its effects on the mechanical properties. The results obtained were satisfactory in terms of the geometry of the base plate and the anchor-rod welding process and tests performed, indicating adequate structural integrity, which is capable of adequately resisting the load generated in the columns of a 4-story building, adequately transmitting the forces and moments to the concrete pedestal and the foundation structure. This study highlights the importance of guaranteeing the quality of the welding process in metallic structures, especially in critical elements such as the base plate - rod anchorage system. As a continuation of this research, it is suggested the implementation of more detailed analyses on the mechanical behavior of welds under real load conditions, as well as the periodic evaluation of the structural integrity in similar buildings. The influence of additional variables, such as the operating environment and the quality of materials, remains to be studied in order to further strengthen the safety and reliability of metallic constructions in Ecuador.Item type:Ítem, Diseño y construcción de un banco de pruebas de ensayos no destructivos para inspecciones mediante partículas magnéticas fluorescentes (MT) para el Laboratorio de materiales de la Carrera de Mecánica(Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, Carrera de Ingeniería Mecánica, 2023-03) ;Fuentes Córdova, José Luis ;Núñez Maliza, Jesús AlejandroParedes Salinas, Juan GilbertoNowadays, the importance of Non-Destructive Testing is reflected in the student field as well as in the educational module taught by the Mechanics career and its application in the national and international industry, a new NDT equipment was provided to the Materials laboratory of the career. For this purpose, an exploratory research was carried out in product data sheets and in the Standard Guide for Magnetic Particles Examination (ASTM E 709 - 21), the equipment was designed, on which the respective calculation and simulation was developed, obtaining a satisfactory modeling for its construction. For the construction of the equipment, processes such as: bending, turning, milling, drilling and SMAW welding were required, in steel A 500 Gr D and ASTM A 36. Regarding the design and construction of the transformer and magnetization system, the Standard Guide ASTM E1444 -15 and ASTM E 709 - 21 were used, establishing a maximum amperage of 1200 A for the Circular and Longitudinal magnetization techniques. Once the construction process of the test bench was completed, its operation was tested by means of its use, in the inspection of several types of specimens by the Circular Magnetization and Longitudinal Magnetization techniques, under the application of the dry and wet fluorescent method. Finally, a manual for the use of the equipment and the development of an instruction manual for the use, storage and maintenance of the suspension of oilbased fluorescent magnetic particles, which is mainly used by the test bench equipment for the development of the inspections, were elaborated.Item type:Ítem, Análisis del proceso de soldadura GTAW y su incidencia en las propiedades mecánicas en juntas a tope del acero AISI 304 empleadas en la industria alimenticia(Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, Carrera de Ingeniería Mecánica, 2023-01) ;Pazmiño Chimbana, Jonathan RicardoVaca Ortega, Wilson HenryIn the food industry, it has been observed that in the manufacture of hoppers there is no analysis of the mechanical properties in butt and bevel weld joints using AISI 304 stainless steel with ER308L, ER309L and ER316L filler material through a GTAW welding process. Among the most relevant mechanical properties we highlight the tensile strength MPa, Brinell hardness (HB) and absorbed energy (J), these mechanical properties can vary by the type of joint, thickness and filler material. The development of this investigative work is based on the AWS D1.6 standard, which establishes general welding parameters for stainless steels, for butt and bevel welding of the plate at 6 mm thickness, the root pass was required., the hot pass and the finish pass while for welding on 3mm thick plates, 2 root and finish passes were carried out. The mechanical tests were carried out in the body building development center of the city of Ambato and with the help of trained technicians, more precise data was obtained from each test carried out. The data obtained in the equipment were tabulated to relate them and to be able to determine which filler material gives us a better mechanical behavior when welding AISI 304 steels.Item type:Ítem, Estudio comparativo entre las juntas de conexión empernadas y por soldadura en el área de acceso vehicular y entre piso de la edificación del parqueadero ubicado en la av. 12 de Noviembre de la ciudad de Ambato y su incidencia en el comportamiento mecánico operacional(Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica. Maestría en Ingeniería Civil con Mención en Estructuras Metálicas, 2022-09) ;Zavala Córdova, Luis EduardoUreña Aguirre, Maritza ElizabethThis degree work is based on a building that was built in the city of Ambato in order to determine what would be the optimum behavior to the requirements established by the structural design standards, for which we proceeded to perform a quantitative analysis in the collection and analysis of results in the comparison of the joints that are currently built by welding, to perform the analysis by connections of RBS and BFP joints, taking into account the criteria of the Ecuadorian Construction Standard (NEC-15), Load and Resistance Factor Design (LRFD) and American Institute of Steel Construction (AISC 360-16), this analysis contributes to the modeling of bolted and welded connections, in order to analyze the localized buckling phenomenon in the wings and web of the metal profiles of the beam-column joint in the vehicular access area and the joint between floors, The results obtained showed that the RBS connection has a better deformation behavior without affecting the web and flanges of the profile, and that the BFP connection cannot be used in the same way as the BFP connection, the BFP connection cannot be used in joints where the inclination of the beam towards the column has a steep slope because the plates must be connected perpendicularly and the welding connection tends to be the most economical and can be used in any area, however it tends to reach the equivalent stressstrain deformation limit, in relation to the cost of materials used for the installation of the BFP joint it is more expensive because it implies placing more supply of elements in the joint.Item type:Ítem, Análisis comparativo de conexiones precalificadas con tipología soldadas y empernadas para un sistema SMF en un edificio de estructura metálica(Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica. Maestría en Ingeniería Civil con Mención en Estructuras Metálicas, 2022-09) ;Merino Mora, Verónica JackelineChávez Rubio, Luis EnriqueEcuador is located in areas where constant and significant earthquakes occur, currently it has been possible to denote the vulnerability of structural steel buildings to a severe earthquake. The scope of this work was to carry out a comparative analysis of prequalified connections with welded and bolted typology for an SMF system in a metal structure building. The ANSI/AISC 360-16 standard is the standard that establishes the specifications for designing steel structures, the ANSI/AISC 341-16 standard indicates the seismic provisions for structural steel buildings and the ANSI/AISC 358-16, which analyzes the prequalified connections for use in special moments and intermediate frames, the standards present a guide for the design of prequalified metallic connections that were used as an instrument for the different mathematical calculations, in addition, applying this methodology, a model of a steel structure was made . National and international standards were used for the study and the Etabs 2019 and Ram Connection software, both with student licenses, were used for the structural analysis. This research performs the comparative analysis of RBS, BFP, BUEEP and WUF-W prequalified connections, with welded and bolted typology for an SMF system in a metal structure building. A structural and economic analysis of the metal frame building is obtained, concluding that the elements that make up the connection in a metal frame building have an elastic behavior. In addition, it was observed that the RBS connection provides the best reliability so that the transfer in the beams (plastic hinge) prevails before that in the columns, as an energy dissipation mechanism and complying with the design philosophy. Regarding the analysis of the cost of steel in beams and columns, it was known that steel in welded beams and columns is cheaper than steel in bolted beams and columns, due to the materials, equipment, machinery and labor used. in the construction process of metal structures.Item type:Ítem, Evaluación de la detectabilidad de discontinuidades en soldadura al variar el agente limpiador en el ensayo de tintas penetrantes Tipo II(Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, Carrera de Ingeniería Mecánica, 2022-09) ;Arcos Aguilar, Christian AlexanderLópez Velástegui, Jorge EnriqueThis experimental work is framed within the area of Non-Destructive Testing: visible penetrant inks used for the inspection of weld discontinuities and focuses on evaluating whether the detectability of discontinuities is altered by varying the cleaning agent. For this purpose, visible dye penetrant tests have been carried out on intentionally produced specimens with surface defects. The data obtained from the tests were analysed in such a way that a control agent (conventional cleaningmagent) was established and compared with the most economical and locally available cleaning/removing agent proposals. In addition, these results were contrasted with tests carried out in Test Panel with fluorescent penetrant inks, to evaluate the detectability of discontinuities from two perspectives. The research is concluded by mentioning the cleaning agents used in the study, placing them in categories: from the agent that does not generate variation in the detectability of discontinuities, to the agent that causes statistically considerable variation in the detectability of discontinuities.Item type:Ítem, Diseño y construcción del sistema mecánico para el ensayo de doblado guiado en juntas soldadas para los laboratorios de la Facultad de Ingeniería Civil y Mecánica(Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, Carrera de Ingeniería Mecánica, 2020-10) ;Abad Sarango, Edgar PatricioAnaluiza Maiza, Oscar IvánFor the elaboration of this technical project, the bibliographic information was compiled from various sources, with this information the first design proposal was made based on the ASTM E190 standard and the AWS B4.0 standard, after several corrections it was obtained a final design, later the design was drawn in software to verify its resistance in the loads and stresses to which it was to be subjected, to obtain a satisfactory result, this project was built with 2 types of materials: A36 steel for its machinability and accessibility in the market and also with 304L stainless steel (UNS S30400) that has a high corrosive resistance, in addition a test procedure and a laboratory guide were carried out, once the construction of the mechanical system was completed, it was installed in the 30-ton hydraulic press that is in the welding laboratory, the operation of all its elements was verified, finally several tests were carried out at different thicknesses with the respective pistons and in compliance with all the procedures dictated by the ASTM E190 standard and the AWS B4.0 standard, after this the tests carried out show reliable results, in this way the proposal prepared has met the requirements of the issue raised.Item type:Ítem, Estudio de la influencia del proceso de soldadura del acero HSLA ASTM A500 GR C utilizado en carrocerías de buses en sus propiedades mecánicas(Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica. Maestría en Mecánica Mención Diseño, 2020-09) ;Carrasco Carrasco, Luis RobertoLópez Villacís, Gonzalo EduardoThis research is intended to define the influence of the heat contributed by the welding process of the bus bodywork on the properties of the material and its capacity of resistance to impact, and for this purpose it began with the testing of ASTM A500 steel without welding. Then, the test was carried out with the E6011 electrode central weld and with the ER70S-6 electrode, measuring the deformation with an initial length of 100mm. It can be effectively verified that the welding process does affect the properties of the material. The most affected property was the modulus of elasticity with a change that exceeded 80 percent, which means that the welding process modified the material making it more rigid and brittle due to the change in temperature and the cooling rate. The yield stress of the material in the welded area decreased to 10 percent, which also reduces the safety factor in this area. Following this, the impact simulation of the front of the bus bodywork was modeled and performed by using the results of the tests in the welding area. The simulation results allowed to identify the areas where the greatest stresses occur, these were located in the area of the frontal collision near the welded joints, but not on the welds. The stress in these areas exceeded the maximum yield stress, but the percentage deformations were less than the tests without breaking the structure.
