Ingeniería Civil y Mecánica

URI permanente para esta comunidadhttp://repositorio.uta.edu.ec/handle/123456789/898

Examinar

Resultados de la búsqueda

Mostrando 1 - 2 de 2
  • Item type:Ítem,
    Influencia de aditivo aireante combinado con macrofibras de polipropileno en hormigones de alta resistencia frente al spalling
    (Universidad Técnica de Ambato-Facultad de Ingeniería Civil y Mecánica-Carrera de Ingeniería Civil, 2026-07-08)
    Yanzaguano Toainga Bryan Daniel
    ;
    Navarro Peñaherrera Carlos Patricio
    ;
    Universidad Técnica de Ambato-Facultad de Ingeniería Civil y Mecánica-Carrera de Ingeniería Civil
    This experimental study analyzes the influence of an air-entraining admixture (AEA) combined with polypropylene macrofibers on the behavior of high-strength concrete subjected to spalling under high temperatures. Seven mix designs (D1–D7) were developed with different air-entraining contents (0.03% and 0.07%) and fiber dosages (1 and 3 kg/m³), producing a total of 105 specimens exposed to temperatures of 20°C, 100°C, 300°C, 700°C, and 1200°C for 3 hours. The results showed that mass loss increases with temperature, reaching values of 20.2% in the control mix at 1200°C, while modified mixtures reduced this value to 11.2%, demonstrating improved thermal stability. Regarding compressive strength, an initial increase was observed at 100°C (up to 136%), followed by a proportional decrease at 300°C, and a significant reduction at 700°C, with values ranging between 21% and 32%. At 1200°C, mixes without fiber exhibited complete failure (0.00 MPa), whereas those incorporating fibers retained residual strength of up to 6.69 MPa. Additionally, spalling was more severe in conventional concrete, while mixtures with AEA and fibers showed reduced disintegration and cracking. It is concluded that their combination helps reduce internal vapor pressure, improve structural integrity, and enhance the residual strength of concrete under extreme thermal conditions.E
  • Item type:Ítem,
    Análisis del comportamiento a flexión del hormigón reforzado con fibras plásticas (polipropileno) después de las altas temperaturas
    (Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, Carrera de Ingeniería Civil, 2023-09)
    Murillo Estrada, Ariel Mateo
    ;
    Ramírez Cabrera, Wladimir José
    Reinforced concrete is one of the most widely used structural elements in Ecuadorian constructions. By the fourth quarter of 2022, 79.5 percent of the material present in the structure was registered, that is, the predominant material in the country. Being so widely used, the question arose how high temperatures affect simple concrete compared to fiber-reinforced concrete. The present work studied the influence of polypropylene fibers in plain concrete after being affected at high temperatures. Obtaining a correct dosage was achieved by analyzing the characteristics of the fine and coarse aggregates, then the required resistance was verified by means of the compression test in cylindrical specimens for resistances of 210 and 240 kg/square centimeters. Once the resistance was obtained, beam-type test tubes of dimensions 10x10x35 centimeters were made where 2 dosages were used with respect to the macrofiber with 0 and 3 kg/cubic meters. After curing the specimens for 28 days, they were subjected to different temperatures: 20, 100, 280 and 600 degrees Celsius. Subsequently, the respective flexural tests (ASTM 1609) were carried out, for the elaboration of the stress vs. deflection graph where the behavior of the concrete without fibers and with fibers was compared. The comparison of the resistances and the addition of fibers in the specimens allowed us to verify the influence of these at high temperatures, improving their resistance to flexion at all exposure temperatures.