Ingeniería Civil y Mecánica
URI permanente para esta comunidadhttp://repositorio.uta.edu.ec/handle/123456789/898
Examinar
12 resultados
Resultados de la búsqueda
Item type:Ítem, Análisis de la dureza y resistencia al desgaste de materiales poliméricos comerciales utilizados en componentes mecánicos(Universidad Técnica de Ambato-Facultad de Ingeniería Civil y Mecánica-Carrera de Ingeniería Mecánica, 2026-07-06) ;Cando Chicaiza Israel Vladimir ;Vaca Ortega Wilson HenryUniversidad Técnica de Ambato-Facultad de Ingeniería Civil y Mecánica-Carrera de Ingeniería MecánicaThis research paper characterizes and evaluates the mechanical and tribological behavior of four commercial engineering polymers Duralon, Grilon, Nylon, and Teflon commonly implemented in the manufacturing of industrial mechanical components. The experimental phase was executed under standardized protocols, conducting indentation hardness tests utilizing a Shore Type D durometer in accordance with the ASTM D2240- 15 standard, and dynamic abrasive wear tests employing a Taber rotary mechanism according to the ISO 9352 specification. Duralon exhibited the highest structural rigidity and the lowest Taber wear index, demonstrating excellent dimensional stability under localized stresses. On the other hand, Teflon, despite registering the lowest surface hardness, achieved highly efficient wear resistance. This behavior is scientifically justified by the activation of an intrinsic molecular self-lubrication mechanism and the subsequent formation of a polymer-to-polymer transfer film on the abrasive wheels. Grilon displayed superior tribological and mechanical performance compared to standard Nylon due to its higher molecular density. Nylon exhibited the highest vulnerability to severe abrasion, driven by friction-induced thermo-mechanical plasticization and its inherent hygroscopic susceptibility. Finally, this mechanical analysis delivers structured material selection criteria for mechanical components, establishing Duralon as the optimal candidate for high structural load configurations, and designating Teflon as the primary alternative for continuous sliding interfaces where external lubrication is technically restrictive.Item type:Ítem, Análisis de las propiedades físico-mecánicas y resistencia de los suelos con la incorporación de la ceniza de hoja de bambú(Universidad Técnica de Ambato-Facultad de Ingeniería Civil y Mecánica-Carrera de Ingeniería Civil, 2026-07-03) ;Santamaria Chávez Franklin Alexis ;Ortiz Montero Santiago AndrésUniversidad Técnica de Ambato-Facultad de Ingeniería Civil y Mecánica-Carrera de Ingeniería CivilThe present research aimed to evaluate the physical-mechanical properties and the strength of two types of soil through the incorporation of bamboo leaf ash (BLA) in proportions of 4 %, 5 %, and 6 %. Two soils of different origin were analyzed: one extracted from the city of Ambato, classified as clayey sand (SC), and another from Santa Clara, classified as silt of medium-low plasticity (ML). The study was carried out in three phases: the characterization of the soils in their natural state, the incorporation of ash in the three indicated proportions, and the technical comparison of the results to determine the optimum proportion of addition. Tests of moisture content, particle-size analysis, Atterberg limits, standard Proctor, and CBR were performed. With the ash, the CBR of both soils increased. That of Ambato rose from 7.90 % to 15.40 % with 5 % ash, and that of Santa Clara from 2.58 % to 5.40 % with 4 %. In the Ambato soil, the behavior became non-plastic upon adding 4 % ash, whereas in the Santa Clara soil the plasticity decreased as each proportion was added. It was concluded that the optimum percentage of ash depends on the type of soil.Item type:Ítem, Análisis comparativo de la resistencia a la compresión de un hormigón tradicional y un hormigón con sustitución del agregado fino por arcilla al 5% y 10% en volumen(Universidad Técnica de Ambato-Facultad de Ingeniería Civil y Mecánica-Carrera de Ingeniería Civil, 2026-07-01) ;Flores Tipan Danny Vladimir ;Navarro Peñaherrera Carlos PatricioUniversidad Técnica de Ambato-Facultad de Ingeniería Civil y Mecánica-Carrera de Ingeniería CivilThis experimental study focused on a comparative analysis of the compressive strength of traditional concrete and concrete in which the fine aggregate was replaced with clay at 5% and 10% by volume, with the aim of conducting a thoro evaluation of the mechanical properties to determine whether replacing the fine aggregate with clay is a feasible option for enhancing the compressive performance of concrete, thereby promoting resource efficiency and environmental responsibility in the industry. Three mixtures were designed using the ACI 2111.1 method for a target strength of 240 kg/cm², including a control sample with 0% clay, one with 5% substitution, and another with 10% substitution. Thirty-six cylindrical specimens were cast and tested at 7, 14, 21, and 28 days in accordance with NTE INEN 1573. The results at 28 days showed that the control concrete exceeded the design strength, reaching 263.77 kg/cm². In contrast, the mixture with 5% clay achieved 237.08 kg/cm², a reductionof 10.1%, and the one with 10% reached 232.16 kg/cm², a reductionof 12.0%. Neither of the two alternative dosages achieved the required structural strength. The decrease in mechanical strength is attributed to the high water demand of the clay, which weakens adhesion in the interfacial transition zone. The experimental results show that replacing fine aggregate with the substitute material reduces compressive strength. Therefore, its use is ruled out for structural concrete with a compressive strength of 240 kg/cm², and lower replacement ratios or its use in non-structural elements should be considered.Item type:Ítem, Análisis de las propiedades mecánicas de la madera de canelo proveniente de la ciudad del Puyo provincia de Pastaza y su factibilidad como material estructural de acuerdo con la norma Ecuatoriana de la Construcción 2015 (NEC 2015)(Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, Carrera de Ingeniería Civil, 2024-08) ;Ponce Romero, Carlos AndrésBayas Altamirano, Myriam MarisolThe objective of this experimental work is to provide information on the mechanical properties of canelo wood (perpendicular bending and traction parallel to the fiber) from the urban parish: Puyo, and the rural parishes: El Triunfo, Veracruz and Tarqui, province of Pastaza, and reveal the maximum stress, modulus of elasticity and resistance to parallel traction and perpendicular bending to the grain that this type of wood presents. The research was based on the ASTM D143-94 regulations for the preparation of the test pieces, in which 6 samples were made for each test and both physical and mechanical properties were determined. In the physical tests, the moisture content was determined in the green or freshly cut state and dry state, which complies with the parameters given by the NTE INEN 896 (2013) standard, while for the mechanical tests the elastic modulus and the admissible stresses in axial bending and parallel traction of each of the parish specimens, governed by the formulas established by the ASTM D198 standard. According to the results of the analyzes given of the 48 samples of canelo wood, it was established that this type of wood can be used as a structural material, since its calculated mechanical properties gave significant values, taking into consideration that the wood Coming from the Puyo urban parish, it had better resistance in parallel traction and perpendicular bending to the fiber.Item type:Ítem, Influencia del tamaño nominal máximo del agregado fino en la resistencia a la compresión del hormigón simple(Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, Carrera de Ingeniería Civil, 2024-02) ;Morejón Ortiz, Anthony XavierPeñafiel Valla, Lourdes GabrielaConcrete, known for its wide use in construction, is distinguished by its high compressive strength. However, certain elements, such as the maximum nominal size of the fine aggregate, can vary this strength. This research addresses how variation in fine aggregate size influences the compressive strength of plain concrete. This project studies the variations in the properties of aggregates with the sizes of #4, #8, #16, #30, #50 and #100 sieves to produce concrete according to NTE INEN standards. To obtain the dosage, the optimum density method of the Central University of Ecuador was used, varying according to the size and properties of the fine aggregate. Two strengths of 240 kg/cm2 and 280 kg/cm2 were considered, then 54 cylindrical specimens of simple concrete were prepared for each strength, 9 specimens for each nominal size of the fine aggregate, which were tested at 7, 14 and 28 days. To ensure control, 3 specimens were tested at each curing time interval and accurate information was obtained to correlate the achieved compressive strength of the plain concrete with respect to the nominal size of the fine aggregate. The results reveal a progressive decrease in compressive strength as the maximum nominal size of the fine aggregate is reduced, manifesting itself noticeably in the final strength at 28 days of curing. Likewise, variations in the properties of the finer aggregate are observed.Item type:Ítem, Influencia del tamaño nominal máximo del agregado grueso en la resistencia a la compresión del hormigón simple(Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, Carrera de Ingeniería Civil, 2024-02) ;Ruiz Gutiérrez, Nicole De Los ÁngelesPeñafiel Valla, Lourdes GabrielaThis project addresses the substantial impact that the coarse aggregate size has on the compressive strength of plain concrete. Considering sizes of 1 inch, 3/4 inch, 1/2 inch, and 3/8 inch, and design strengths of 240 kg/cm2 and 280 kg/cm2, correlations were established between both variables, considering the existing relationship between the mentioned factors. The properties of the materials to be used were determined by applying tests governed by some of the NTE INEN standards. Following this, the concrete mix designs were designed for each nominal maximum size of the coarse aggregate using the Central University of Ecuador's optimum density method. A total of 72 concrete cylinders were produced (9 for each nominal maximum size). 3 cylinders were tested according to each nominal maximum size at 7, 14, and 28 days, obtaining the necessary information for the data analysis, allowing the establishment of correlations between the nominal maximum size of the coarse aggregate and the compressive strength. The results showed a coefficient of -0.60, indicating that as the nominal maximum size of the aggregate is reduced, strengths above 100 percent of the design strength can be obtained. Similarly, when proposing correlations with the hardened density of the concrete, this coefficient was 0.74, which means that the density has a greater influence than the size. This only occurs for the sizes mentioned in this study.Item type:Ítem, Diseño y construcción de un accesorio externo automotriz bajo el proceso de infusión al vacío con material compuesto de matriz polimérica(Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, Carrera de Ingeniería Mecánica, 2024-02) ;Tenorio Cabezas, Vanessa EstefaníaParedes Salinas, Juan GilbertoActually the application of composite materials for the forming and creation of components or accessories is one of the greatest needs in the industrial field, aiming to reduce the weight and the replacement of metals, preserving or improving the properties of the materials. The progress of the forming processes are mostly manual, causing irreversible failures such as porosity, cracks, air bubbles and more defects, forming less resistant laminates. The Technical Project focused on obtaining the main parameters involved in the vacuum infusion process applied to a laminate with a complex shape, that is, curved, inclined, straight and deep areas. In addition, Tensile-Flexural tests were carried out to check the mechanical properties of the laminate obtained and cured at a temperature of 80 grades Celsius for two hours. The results obtained through the application of the process were compared with other commercial projects that were formed under the same parameters. The technical work showed that for a vacuum infusion process, permeability is one of the parameters that influenced at the time of lamination, using and applying Darcy's Law, for that reason it was important to select the complements (vacuum infusion kit) and it was verified that the orientations of the natural or synthetic fibers should be at 45 grades for greater resistance, but if a laminate with lower residence is desired, the recommended orientation is from 0 to 90 grades.Item type:Ítem, Modelo de material para perfiles conformado en frío de sección transversal UV de acero a36, para espesores de 10 mm y 12 mm(Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, Carrera de Ingeniería Mecánica, 2024-02) ;Caiza Llumitasig, Edisson Dario ;Pullutasig Chuquisala, David AndrésPeña Jordán, Francisco AgustínThe material model obtained for cold-formed UV cross-section profiles of ASTM A36 steel, for thicknesses of 10 mm and 12 mm, is presented as a versatile and efficient structural solution. This model has been developed considering its mechanical properties and its usefulness in the construction industry due to its resistance and ease of forming. To analyze the impact of the mechanical properties in the cross section of the profile obtained, three types of tests were carried out. In the tensile test, the ASTM E8 standard was applied, evaluating its mechanical properties, taking into account the tensile strength, elastic limit and modulus of elasticity in the specimens of the different sections (wings, back, curves) of the profile. Using the ASTM E10 standard, the hardness test was carried out on specimens extracted for each thickness, determining their hardness in the virgin material and in the cross section of the UV profile. Using the ASTM E-112 standard, the metallographic test was applied, obtaining micrographic photographs of the grains of the virgin material and the affectation in the cross section of the UV profile. As a result, the mechanical tests carried out show a comprehensive view of the mechanical properties in the cross section of the UV profile, highlighting a greater rigidity in the 12 mm profile and a greater impact on the mechanical properties in the curved sections of the profile, reaching maximum stresses. tensile strength of 551.5 MPa and 554.21 MPa for thicknesses of 10 mm and 12 mm.Item type:Ítem, Diseño y construcción de una máquina para ensayos de tensión que caracterice los efectos que producen los cambios de geometría en una probeta plana(Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, Carrera de Ingeniería Mecánica, 2023-09) ;Bastidas Sarabia, Bryan Isaias ;Gamboa Sangoquiza, Luis FernandoArroba Arroba, César HernánTensile tests are important to understand the mechanical behavior of different materials when subjected to different loads and conditions. These tests allow understanding the different properties such as strength, elasticity, ductility, and stiffness of the element, being crucial for the design and selection of materials in industrial and structural applications. However, it is necessary to keep in mind that geometry changes in flat specimens have a significant impact on the mechanical behavior of the materials while they are subjected to stress. These changes include variations in the cross section, due to the presence of holes or different geometrical irregularities generating a concentration of stresses and different localized deformations. This is the reason why the necessary knowledge is provided to design and build a machine that allows visualizing the geometry changes that originate in a specimen. Previous research on the subject was carried out, continuing with design ideas, and following the design parameters given by the book "Shigley's Design in Mechanical Engineering". Once the design and analysis were done in the different softwares, we proceeded to verify plans for the construction of the prototype. Once the machine was built, the calibration and printing of different specimens was carried out.Item type:Ítem, Análisis comparativo del índice de inflamabilidad horizontal bajo la norma ISO 3795, entre materiales compuestos de matriz poliéster reforzado con fibras naturales (fibra de cabuya, fibra de chambira, fibra de coco y fibra de totora) frente a la fibra de vidrio(Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, Carrera de Ingeniería Mecánica, 2023-09) ;Chaglla Toapanta, Bryan JoelCastro Miniguano, Christian ByronToday, the use of composite materials is very common in various professional and industrial applications, so it is necessary to ensure that the materials meet a high level of safety for the end user. Creating composite materials lies in the sole purpose of improving their properties, therefore, in the present investigation it is intended to evaluate and compare the fire resistance of polymer matrix composite materials reinforced with natural fibers (cabuya, chambira, coconut and totora) against a synthetic fiber (fiberglass), allowing us to consider a possible substitution of synthetic materials for environmentally friendly materials, which could open a new market for their commercialization. In order to establish the appropriate percentages for the formation of composite materials, the volumetric fractions of previously carried out titling works were taken into consideration, where the percentages that provide the best characteristics of the material are detailed, having these values, the amount of resin, fiber and catalyst necessary for each configuration was calculated, after that, all these components were placed in the mold sized according to the NTE INEN ISO 3795 standard, applying manual compression on each material, once the process was completed, it was necessary to you have to wait for the curing time and verify that the new material is fully solidified. Once the samples were ready, they were sent to the LIM-UTA Mechanical Research Laboratory, to be tested, finally the combustion rate of each material was obtained, where an average of 3.61 mm/min was recorded for the Cabuya fiber, 6.72 mm/min for the Chambira fiber, 4.91 mm/min for the coconut fiber, 8.46 mm/min for the reed fiber and 9.18 mm/min for the glass fiber. Based on the results, it was possible to determine that the cabuya fiber-reinforced polyester resin composite material with a value equivalent to 3.61 mm/min is the material with the lowest propagation index compared to the other fibers evaluated.
