Por favor, use este identificador para citar o enlazar este ítem:
https://repositorio.uta.edu.ec/jspui/handle/123456789/29768
Título : | Diseño y construcción de una mini turbina tipo tornillo de Arquímedes para ser instalada en canales primarios abiertos y generar energía mecánica |
Autor : | Escobar Luna, Luis Eduardo Lucio Yugsi, Daniel Mesías |
Palabras clave : | MINI TURBINA TIPO TORNILLO TORNILLO DE ARQUÍMEDES CANALES PRIMARIOS ENERGÍA MECÁNICA ENERGÍA HIDROELÉCTRICA MÁQUINAS HIDRÁULICAS CANALES DE REGADÍOS ECUACIÓN DE CONTINUIDAD ECUACIÓN DE ENERGÍA ECUACIÓN DE PÉRDIDAS |
Fecha de publicación : | 2019 |
Editorial : | Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, Carrera de Ingeniería Mecánica |
Resumen : | Using the data obtained in the channel, the mechanical and hydraulic design of the mini screw-type turbine of archimedes was carried out, for which it was of great need to use several documents of previous works on the subject, however, the most relevant document was "Design of a hydraulic turbine based on the screw of Archimedes", which is a thesis made by Julio Cesar Alberto Mejía. Most of the screw was made with A36 steel, except for the axle, and the bearings, these materials were not manufactured, but only purchased on the market. An optimal design was carried out for which the measurements of the channel, the weight of the structure, its assembly and transport were taken into account. It was determined that the construction of the turbine should have a length of 3 meters, a width of 2 meters and a height of 1 meter, with the tests the revolutions delivered by the mini turbine were measured, resulting in values between 125 and 160 rpm. Finally, taking into account all the tests, it was noted that at the exit of the ovals, a greater water velocity is obtained. |
Descripción : | Para la elaboración de este proyecto técnico se utilizó datos obtenidos en el canal de riego Huachi-Pelileo, se procedió al diseño mecánico e hidráulico de la mini turbina tipo tornillo de Arquímedes, para lo cual fue de gran necesidad el uso de varios documentos de trabajos previos referentes al tema. La mayor parte del tornillo se lo realizó con acero A36, exceptuando el eje, y las chumaceras, estos materiales no fueron fabricados, sino solo se adquirió en el mercado. Se realizó un diseño óptimo para el cual se tomó en cuenta las medidas del canal, el peso de la estructura, su montaje y transporte. Por medio de cálculos según el modelo teórico de la turbina se obtuvo una potencia que se encuentra en el rango de 335 a 380 W y un torque de entre 15 a 25 Nm. Se determinó que la construcción de la turbina debe tener un largo de 3 metros, un ancho de 2 metros y una altura de 1 metro, con las pruebas se midió las revoluciones entregadas por la mini turbina dando como resultados valores entre 125 a 160 rpm. Por último, tomando en cuenta todas las pruebas, se pudo notar que en la salida de los óvalos se obtiene una mayor velocidad del agua. |
URI : | http://repositorio.uta.edu.ec/jspui/handle/123456789/29768 |
Aparece en las colecciones: | Ingeniería Mecánica |
Ficheros en este ítem:
Fichero | Descripción | Tamaño | Formato | |
---|---|---|---|---|
Tesis I. M. 518 - Lucio Yugsi Daniel Mesías.pdf | TESIS A TEXTO COMPLETO | 3,77 MB | Adobe PDF | Visualizar/Abrir |
Los ítems de DSpace están protegidos por copyright, con todos los derechos reservados, a menos que se indique lo contrario.