Por favor, use este identificador para citar o enlazar este ítem: https://repositorio.uta.edu.ec/jspui/handle/123456789/30026
Título : La adición de aserrín y poliestireno en la elaboración de bloques de adobe para viviendas unifamiliares y su efecto en la variación de temperatura y acondicionamiento acústico en el cantón Ambato, provincia de Tungurahua
Autor : Núñez Aldás, Galo Wilfrido
Pino Escobar, Holguer Alejandro
Palabras clave : ASERRÍN
POLIESTIRENO
BLOQUES DE ADOBE
VIVIENDAS UNIFAMILIARES
VARIACIÓN DE TEMPERATURA
ACONDICIONAMIENTO ACÚSTICO
HERRAMIENTAS MENORES
ENSAYO TÉRMICO
ENSAYO ACÚSTICO
CINTA DE BARRO
RESISTENCIA SECA
LÍMITES DE ATTERBERG
TRASNSMITANCIA TÉRMICA
CONFORT ACÚSTICO
Fecha de publicación : 2019
Editorial : Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, Carrera de Ingeniería Civil
Resumen : The present experimental work evaluated the use of sawdust and polystyrene in the elaboration of blocks of adobe to determine the variation of temperature and acoustic conditioning. Firstly, a soil selection and analysis process were carried out based on the E-080 standard, later, traditional adobe blocks and adobe blocks were prepared with a percentage of 5%, 10% and 15% of sawdust and polystyrene in addition to each mixture. The blocks were tested under compression in the course of 28 days from its preparation, the test showed that all the samples analyzed exceeded the minimum resistance of 1MPa established in the E-080 Standard, but the highest compressive strength obtained was 2.66 MPa in blocks with 5% sawdust and polystyrene, thus exceeding the minimum resistance by 50%. Before making the test, adobe walls were made with each percentage of additives established, which were assembled inside the chamber, consecutively they were put to the thermal analysis based on the NCh 851 - NCh 849 norms and acoustic based on the norm NCh 2865. Finally, when quantifying the results, it was found that the wall made with adobes plus 5% and 15% sawdust and polystyrene maintains the best thermal variation and acoustic conditioning in such a way that it was selected as the best block prototype for the present investigation.
Descripción : El presente trabajo experimental evaluó el uso del aserrín y poliestireno en la elaboración de bloques de adobe para determinar la variación de temperatura y acondicionamiento acústico. En primer lugar, se realizó un proceso de selección y análisis de suelo en base la Norma E-080, posteriormente se elaboró bloques de adobe tradicionales y bloques de adobe con un porcentaje de 5%, 10% y 15% de aserrín y poliestireno en adición a cada mezcla. Los bloques fueron ensayados a compresión en el transcurso de 28 días desde su elaboración, el ensayo demostró que todas las muestras analizadas superaron la resistencia mínima de 1MPa establecido en la Norma E-080, pero la mayor resistencia a compresión obtenida fue 2.66 MPa en bloques más 5% de aserrín y poliestireno, superando así en un 50% a la resistencia mínima. Previo a realizar el ensayo se elaboraron muretes de adobe con cada porcentaje de aditivos establecido, los mismos que fueron ensamblados en el interior de la cámara, consecutivamente fueron puestos al análisis térmico en base a las normas NCh 851 - NCh 849 y acústico en base a la norma NCh 2865. Finalmente, al cuantificar los resultados se constató que el muro elaborado con adobes más 5% y 15% de aserrín y poliestireno mantienen una buena variación térmica y acondicionamiento acústico, de tal manera que fue seleccionado como el mejor prototipo de bloque para la presente investigación.
URI : http://repositorio.uta.edu.ec/jspui/handle/123456789/30026
Aparece en las colecciones: Ingeniería Civil

Ficheros en este ítem:
Fichero Descripción Tamaño Formato  
Tesis I. C. 1344 - Pino Escobar Holguer Alejandro.pdfTESIS A TEXTO COMPLETO3,3 MBAdobe PDFVisualizar/Abrir


Los ítems de DSpace están protegidos por copyright, con todos los derechos reservados, a menos que se indique lo contrario.