Por favor, use este identificador para citar o enlazar este ítem: https://repositorio.uta.edu.ec/jspui/handle/123456789/30657
Título : Análisis de la influencia de los rayos UV en la resistencia a la tracción del compuesto de matriz polimérica reforzada con fibra de guadua
Autor : Pérez Salinas, Cristian Fabián
Guamani Saquinga, Marisol Belén
Palabras clave : RAYOS UV
RESISTENCIA A LA TRACCIÓN
MATRIZ POLIMÉRICA
FIBRA DE GUADUA
POLÍMEROS TERMOPLÁSTICOS
POLÍMEROS TERMOESTABLES
MATERIALES AVANZADOS
MATERIAL COMPUESTO
ENSAYO DE EXPOSICIÓN UV
RADIACIÓN
Fecha de publicación : 2020
Editorial : Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, Carrera de Ingeniería Mecánica
Resumen : In the present experimental work was analyzed the influence of UV rays on the tensile stress of the polymer matrix composite material, through a mechanical test where it was determined that guadua fiber has good mechanical properties. It is similar the behavior of a fiber synthetic, so this fiber can replace it. The great abundance, it was facilitated to obtain and process the fibrous material. The composite material has as a matrix the polyester and epoxy resin while the reinforcement is considered guadua fiber, which It should be woven with an orientation of 0 degrees at the time of being used as reinforcement and stacking layers. As the way to improve the mechanical properties. Thense, the Guadua fiber reinforced polymer matrix composite material has a volumetric fraction of 70 percent as matrix and 30 percent as reinforcement by hand lay-up and cured to the environment for 720 hours at room temperature. The analysis of the tensile strength behavior of the composite material by ASTM D3039 regulations was performed when subjected to a UV test by ISO 4892 for 50 hours and 250 hours of exposure in an artificial aging chamber with xenon arc. Also, the tensile test was performed with 30 specimens classified by resin and epoxy matrix at 0, 50 and 250 hours of exposure. When the data is obtained, the statistical analysis is carried out using the Minitab software allows an statistic analysis of the data. Then it was determined that the maximum tensile stress of 84.63 MPa, modulus of elasticity of 1363.03 MPa and elongation of 6.21 percent with polyester resin matrix and a the maximun resistance of 71.79 MPa, modulus elasticity of 1518.47 MPa and elongation of 4.73 percent with epoxy resin matrix. And the use of the desirability function it was determined that the best combination when the material has a polyester matrix exposed to 250 hours of UV rays. It is demonstrating the better behavior with these characteristics. It is an economical resin to provide the rigidity and resistance to the composite material and where exposure to UV rays improves the mechanical property.
Descripción : En el presente trabajo experimental se analizó la influencia de los rayos UV en la resistencia a la tracción del material compuesto de matriz polimérica, mediante un ensayo mecánico donde se determinó que la fibra de guadua posee buenas propiedades mecánicas que se asemejan al comportamiento de una fibra sintética, por lo cual esta fibra puede reemplazarla. Debido a la abundancia de esta, facilitó su obtención y procesamiento del material fibroso. El material compuesto tiene como matriz la resina poliéster y epoxi mientras que como refuerzo se considera a la fibra de guadua, misma que deberá ser tejida con una orientación de 0 grados al momento de ser usada como refuerzo y con apilamiento de capas, puesto que de esta forma se mejora las propiedades mecánicas. Por lo tanto, el material compuesto de matriz polimérica reforzada con fibra de Guadua posee una fracción volumétrica de 70 por ciento matriz y 30 por ciento refuerzo con estratificación manual y curado al medio ambiente durante 720 horas a temperatura ambiente. Se realizó el análisis del comportamiento de la resistencia a la tracción del material compuesto bajo normativa ASTM D3039 cuando es sometido a un ensayo de rayos UV bajo normativa ISO 4892 durante 50 horas y 250 horas de exposición en una cámara de envejecimiento artificial con arco de xenón. También, se realizó el ensayo a tracción con 30 probetas clasificadas por matriz resina y epoxi a 0,50 y 250 horas de exposición. Con los datos obtenidos se procede al análisis estadístico mediante el software Minitab que permite tener un análisis estadístico de los datos. Luego se determinó que la resistencia a la tracción máxima alcanza un valor de 84,63 MPa, módulo de elasticidad de 1363,03 MPa y elongación de 6,21 por ciento con matriz de resina poliéster y una resistencia de 71,79 MPa, módulo de elasticidad de 1518,47 MPa y elongación de 4,73 por ciento con matriz de resina epoxi. Y con el uso de la función de deseabilidad se determinó que la mejor combinación se alcanza cuando el material tiene matriz poliéster expuesto a 250h de rayos UV, demostrando un mejor comportamiento con dichas características. Además de ser una resina económica le proporciona rigidez y resistencia al material compuesto y donde la exposición a los rayos UV mejoran la propiedad mecánica notablemente.
URI : https://repositorio.uta.edu.ec/jspui/handle/123456789/30657
Aparece en las colecciones: Ingeniería Mecánica

Ficheros en este ítem:
Fichero Descripción Tamaño Formato  
Tesis I. M. 578 - Guamaní Sanquinga Marisol Belén.pdfTESIS A TEXTO COMPLETO21,49 MBAdobe PDFVisualizar/Abrir


Los ítems de DSpace están protegidos por copyright, con todos los derechos reservados, a menos que se indique lo contrario.